4K-DVI fiber extenders also named as 4K DVI to fiber converter or 4K DVI fiber
transmitter and receiver,which transmit 1CH uncompressed HD DVI
signal over 1 single-mode or multimode optical fiber without delay
.It supports maximum resolution of 4096 x 2160@30HZ DVI signal to
reach 10 km transmission over single-mode fiber or 300 meters over
multimode (Gigabit OM3) .
Product features
1 ,extend DVI signal ,transmit uncompressed HD DVI signal without
delay
2, maximum resolution 4096 x 2160@30HZ, support 2K/4K resolution;
3 ,10 km transmission over single-mode fiber or 300 meters over
multimode (Gigabit OM3) .
4,RGB video signal clock, non TMDS extension
5, transmitter EDID EEPROM reset (EDID manual read)
6,no EMI electromagnetic interference, lightning protection
7, support DDWG (digital display working group)
8, easily install,small and flexible
Application range
Urban traffic monitoring system
Public security, safe city monitoring system
Highway security and charging system
Industrial control (airport, chemical, steel, petroleum, railway,
water conservancy, mining, etc.)
Military command system, military surveillance (warehouse, frontier
defence, guard, national defence, etc.)
Gymnasium (live video, audio transmission)
Television program transmission system, live broadcast, high
definition video conference system
specification:
Opitcal:
| Wavelength | 850nm &1310nm |
| Output Power | -6~-1dBm |
| Optic fiber | OM3 multimode ,9/125u single mode |
| Rx sensitivity | -16dBm |
| Optical connector | 1 x LC |
| Distance | 0~300M (OM3 MM) / 0~10KM (SM) |
Video:
| Output video | DVI 1.0 |
| Input video signal | 0.5～1.0V P-P |
| Input signal DDC | 5V P-P (TTL) |
| Connector | 18+1 DVI Male |
| General: |
| Input Power | 5 V DC |
| Power consumption (maximum) | 2.4W(max) |
| Operating temperature | -20°C to 70°C |
| Storage temperature | -40°C to 85°C |
| Operating humidity | 0 ~ 95% (non-condensing) |
| Net Weight | 200g per pair |
| Case material | Aluminum |
| Product size | 64mm×52mm×22.5mm |
System installation requirements
hardware requirements
In your PC, SUN or Mac system in the DVI image controller or card
exists a DVI port ,and must support the maximum image resolution of
the monitor. If you have installed the DVI image controller or
card, there's no special limit for memory, CPU speed and chipset.
Software requirements
If you have installed the DVI image controller in your OS, there is
no special limit.
Equipment installation and operation
Note: please use as the following setup,or the device may not work
properly.
Step 1: respectively turn on the power of PC and monitor, .
Step2: read the EDID of the monitor,please follow the following
steps:
(1) connect the 5V power adapter to the DVI transmitter (this
sequence must be correct), then the red power indicator light on.
(2) open the power of the monitor, then connect the DVI interface
of the DVI transmitter to the DVI interface of the display device.
(3) press the "W/R" EDID to reading button on the right side of the
transmitter power , the indicator lights flashing green, after 2
seconds or 3 seconds , the green lights off, it means EDID read and
write success. After this,turn off the power of the transmitter,
then remove the transmitter.
The lights state of Power and EDID reading and writing : normally
the red light on when power works, the green light on when the EDID
is reading and writing.
Note: if you change the other monitor, please do the second step
again.
Step3: Connect the 5V power adapter to DVI transmitter (this
sequence must be correct), and then connect the transmitter's DVI
interface and PC's DVI interface
Step4: Connect 5V power adapter to the receiver, the power lights
turn red, then connect the receiver's DVI interface to monitor's
DVI interface.
Step5: LC fiber connection.
4K-DVI fiber extenders Application:
